Ontologie aéronef active
Chantier historique
MSN non renseigné
Changer d’aéronef
Rattachement des étapes aux composants
Chaque étape de retrait doit désigner le composant qu'elle enlève. La relation dernière opération de l'étape → ENLÈVE → composant est proposée ici, déduite du sous-système visé par le processus et du nom de l'étape. Pour chaque cas douteux, le bouton 🔍 Examiner ouvre une fenêtre avec le contexte complet et les pistes classées. Rien n'est écrit en base tant que vous ne validez pas.
Rattachement supprimé.
Rattachements ENLÈVE déjà en base
149
| Étape | Opération | Composant enlevé | Action |
|---|---|---|---|
| A. Remove Air Outlet Valve (Wemac) | (4) Remove air outlet valve and adapter | Air Outlet Valve (Wemac) | Supprimer |
| inconnue | (6) Remove the fan from the airplane | Primary Flight Display (PFD) Fan | Supprimer |
| A. Remove the Deck Skin Fan | (6) Remove the fan from the airplane | Deck Skin Fan | Supprimer |
| A. Remove the Control Cable | (7) Carefully remove the cable from the instrument panel and firewall | Cabin Heat Control Cable | Supprimer |
| A. Remove Autopilot (Single-Axis) Flight Computer | (3) Pull autopilot flight computer out and away from mounting tray | KC-140 (Single-Axis) Autopilot Flight Computer | Supprimer |
| A. Remove Roll Servo | (5) Remove roll servo from airplane | Roll Servo | Supprimer |
| inconnue | (10) Remove the servo from the airplane | Roll Servo and Cable | Supprimer |
| A. Remove Pitch Servo Actuator | (5) Remove the pitch servo actuator from the airplane | Pitch Servo Actuator | Supprimer |
| A. Remove the Pitch Trim Servo | (6) Remove the pitch trim servo from the airplane | Pitch Trim Servo and Cable | Supprimer |
| inconnue | (7) Remove the unit from the mounting rack | GIA-63 Integrated Avionics Unit | Supprimer |
| A. Remove the NAV Antenna | (4) Carefully remove thet fillet seal from the junction of the NAV antenna and the skin of the airplane | NAV Antenna | Supprimer |
| A. Remove the Microphone Switch | (3) Lift up the escutcheon to get access to the microphone switch and disconnect the microphone switch from the control wheel connection | Microphone Switch | Supprimer |
| A. Remove the Audio Panel | (3) Carefully pull the audio panel out from the tray and disconnect the electrical connectors from the audio panel | Audio Panel | Supprimer |
| C. Remove Rear Passenger Intercom Jacks | (6) Loosen and remove jamnuts securing jacks to rear sidewall panel | Intercom Jacks | Supprimer |
| A. Remove the Standby Battery | (7) Carefully remove the battery from the airplane | Standby Battery | Supprimer |
| A. Remove the Standby Battery PC Board | 8) If applicable, put the PC board in an electrostatic safe bag | Standby Battery PC Board | Supprimer |
| A. Remove the Power Junction Box | (7) Remove the power junction box from the airplane | Power Junction Box | Supprimer |
| A. Seat Removal | (5) Remove the seat from the airplane | Seat | Supprimer |
| A. Remove the Seat Recline Control Assembly | (a) Pull the control assembly with cable through the seat bracket and remove it from the seat | Seat Recline Control Assembly | Supprimer |
| A. Remove the Height Adjustment Handle Assembly | (b) Remove the height adjustment handle assembly from the seat | Seat Height Adjustment Handle Assembly | Supprimer |
| A. Remove Map Compartment | (1) Remove interior screws securing map compartment to instrument panel structure | Map Compartment | Supprimer |
| A. Restraint System Removal | (b) Carefully remove the EMA from the airplane | Inflatable Restraint System | Supprimer |
| A. Pilot's and Copilot's Restraints Removal | (3) Remove nuts, washers, bolts and bushing securing restraint assembly to seats | Seat Belt/Restraints | Supprimer |
| E. Bench Seat Restraints Removal | (2) Remove bolts, washers, and bushings securing restraint inertia reels to seat frames | Seat Belt/Restraints | Supprimer |
| A. Center Seat Removal | (4) Remove seat from airplane | Center Seat | Supprimer |
| A. Seat Rail Removal | (1) Remove bolts securing seat rails to fuselage | Seat Rail | Supprimer |
| A. Cargo Pack Removal | (c) Install original the left and right main landing gear fairings. Refer to Chapter 32, Main Landing Gear - Maintenance Practices | Cargo Pack | Supprimer |
| A. ELT Antenna Removal | (8) Remove the ELT antenna from the inside of the airplane | ELT Antenna | Supprimer |
| A. ELT Battery Pack Removal | (4) Remove the ELT battery pack from the ELT | Pointer ELT Battery Pack | Supprimer |
| A. ELT Remote Switch Removal | (8) Remove the ELT remote switch from the airplane | ELT Remote Switch | Supprimer |
| A. ELT Antenna Removal | (8) Remove the ELT antenna from the airplane | ELT Rod Antenna | Supprimer |
| A. Remove the Emergency Locator Transmitter (ELT) | (6) Remove the ELT from the airplane | Emergency Locator Transmitter (ELT) | Supprimer |
| A. Remove the ELT Buzzer | (6) Remove the buzzer from the bracket | ELT Buzzer | Supprimer |
| A. Carbon Monoxide Detector Removal | (5) Remove the CO detector from the airplane | Carbon Monoxide Detector | Supprimer |
| A. Remove Rudder Cables | (11) Remove rudder cables | Rudder Control Cables | Supprimer |
| A. Remove Elevator | (5) Using care, remove elevator | Elevator | Supprimer |
| A. Remove Cables and Pulleys | (9) Remove cables | Cables and Pulleys | Supprimer |
| A. Remove Elevator Bell Crank | (7) Remove bell crank | Elevator Bell Crank | Supprimer |
| A. Remove Aft Elevator Arm Assembly | (4) Remove pivot bolt securing arm assembly and slide assembly from between elevator torque tubes | Aft Elevator Arm Assembly | Supprimer |
| A. Remove Trim Tab Actuator | (9) Remove screws attaching actuator to bracket, and carefully work actuator out through access opening | Trim Tab Actuator | Supprimer |
| A. Remove Cables and Pulleys | (13) Disengage chains from sprockets and remove cables from airplane structure | Trim Tab Control Cables and Pulleys | Supprimer |
| A. Remove the Flap Motor and Transmission Assembly | (8) Carefully remove the assembly from the wing through the access opening | Flap Motor and Transmission Assembly | Supprimer |
| A. Remove the Flaps | (6) Remove the bolts at each flap track. As the flap is removed from the wing, all of the washers, rollers and bushings will fall. Keep this hardware for installation | Flap | Supprimer |
| A. Remove the Cables and Pulleys | (9) Leave the wire in place, routed through structure | Cables and Pulleys | Supprimer |
| A. Remove the Electric Auxiliary Fuel Pump | (9) Loosen the clamps to the pump and remove the pump from the airplane | Electric Auxiliary Fuel Pump | Supprimer |
| B. Remove the Indicator | (3) Remove the screws that attach the indicator to the instrument panel and remove the indicator from the airplane | Fuel Quantity Indicator | Supprimer |
| A. Remove the Timer for the Propeller Heat | (4) Remove the timer from the airplane | Propeller Heat Timer | Supprimer |
| A. Remove Pilot's Center panel | (6) Remove panel assembly | Pilot's Center Panel | Supprimer |
| A. Remove Pilot's Inboard/Outboard Panel | (6) Remove panel assembly | Pilot's Inboard/Outboard Panel | Supprimer |
| A. Remove Copilot's Panel | (5) Remove panel assembly | Copilot's Panel | Supprimer |
| A. Remove the Center Panel | 5) Install tags for identification on the electrical connectors and hoses and disconnect them from the instruments | Center Panel | Supprimer |
| A. Remove the Main Landing Gear Speed Fairing | (5) Loosen the scraper if necessary, and remove the main-wheel speed-fairing from the wheel | Main Landing Gear Speed Fairing | Supprimer |
| A. Remove the Main Landing Gear Brake Fairing | (3) Remove the brake fairing from the landing gear | Main Landing Gear Brake Fairing | Supprimer |
| A. Remove the Main Landing Gear | (b) Identify the shims to be sure they are replaced correctly after the installation of the landing gear | Main Landing Gear | Supprimer |
| A. Remove The Main Landing Gear Brake Clip | (3) Remove all deep nicks or scratches | Main Landing Brake Clip | Supprimer |
| A. Remove the Nose Wheel Speed Fairing | (7) Turn the speed fairing 90 degrees to the center line of the airplane and move the fairing down over the fork to remove | Nosewheel Speed Fairing | Supprimer |
| A. Remove the Nose Landing Gear | (7) Remove nose gear | Nose Landing Gear | Supprimer |
| A. Shimmy Damper Removal | (3) Remove the shimmy damper. For airplanes with the Lord Shimmy Damperi installed, discard the Lord Shimmy Damper. Do not do a disassembly/assembly of the Lord Shimmy Damper | Shimmy Damper | Supprimer |
| A. Remove the Main Wheel Axle | (7) Remove nuts, washers, and bolts that attach the shims, axle, brake components, and speed fairing mounting plate from the strut | Main Wheel Axle | Supprimer |
| A. Floodlight Bulb Removal | (4) Remove the bulb | Floodlight Bulb | Supprimer |
| A. Light Assembly Removal | (4) Remove the light assembly from the overhead console | Light Assembly | Supprimer |
| A. Potentiometer Removal | (5) Remove the potentiometer from the overhead console | Potentiometer | Supprimer |
| A. Oxygen Panel Light Assembly Removal | (3) Remove the cap, washer, and light assembly from the oxygen panel | Oxygen Panel Light Assembly | Supprimer |
| A. Remove the Dimming Assembly | (6) Remove the dimming assembly from the airplane | Dimming Assembly | Supprimer |
| A. Remove Dimming Control | (6) Remove dimming control from airplane | Radio Lighting Dimming Control | Supprimer |
| (1) Remove Wing Tip Navigation Light Lamp | d) Grasp lamp, depress slightly and turn counterclockwise to release and remove lamp from bayonet mount | Navigation Light Lamp | Supprimer |
| (1) Remove Tail Navigation Light Lamp | (d) Grasp lamp, depress slightly and turn counterclockwise to release and remove lamp from bayonet mount | Navigation Light Lamp | Supprimer |
| A. Remove Strobe Tube Assembly | (5) Remove strobe tube assembly from base assembly and remove from wing tip | Strobe Tube Assembly | Supprimer |
| A. Remove Strobe Power Supply | (5) Remove strobe power supply from airplane | Strobe Power Supply | Supprimer |
| A. Remove the LED strobe light assembly | (6) Remove the LED strobe light assembly from the wing-tip | LED Strobe Lights | Supprimer |
| A. Remove Flashing Beacon Lamp | (4) Remove lamp assembly from flasher base assembly | Flashing Beacon Lamp | Supprimer |
| inconnue | (5) Disconnect the electrical wires from the back side of the light and remove the light from the airplane | Light | Supprimer |
| A. Remove the HID ballast | (6) Remove the HID ballast from the airplane | High-Intensity Discharge (HID) Ballast | Supprimer |
| A. Remove the LED Landing, Taxi and Recognition (LTR) Light | (a) Remove the light from the bracket | LED Landing, Taxi and Recognition Light | Supprimer |
| inconnue | (c) Remove the bulb from the airplane | Courtesy Light Lamp | Supprimer |
| A. Pitot Tube Assembly Removal | (6) Remove the pitot tube assembly from the airplane | Pitot Tube Assembly | Supprimer |
| A. Sump Assembly Removal | (4) Remove sump assembly from airplane | Sump Assembly | Supprimer |
| A. Blind Encoder Removal | (5) Remove the blind encoder from the airplane | Blind Encoder | Supprimer |
| A. Altimeter Indicator Removal | 8) Remove the altimeter from the airplane | Altimeter Indicator | Supprimer |
| inconnue | (8) Remove the airspeed indicator from the airplane | Airspeed Indicator | Supprimer |
| A. Remove Outside Air Temperature Indicator | (4) Remove OAT indicator from airplane | Outside Air Temperature Indicator | Supprimer |
| A. Remove the OAT Sensor | (5) Remove the OAT sensor from the airplane | Outside Air Temperature (OAT) Sensor | Supprimer |
| A. Remove the GDC-74 Air Data Unit | (5) Disconnect the hose and the electrical connector from the air data unit | GDC-74 Air Data Unit | Supprimer |
| A. Remove Stall Detector | (7) Remove stall detector from airplane | Stall Detector | Supprimer |
| A. Remove the SCc Lift Transducer | (3) Remove the lift transducer from the aircraft | Safe Flight SCc AOA Lift Transducer | Supprimer |
| A. Horizon Gyro Removal | (9) Remove the horizon gyro from the airplane | Horizon Gyro | Supprimer |
| A. Directional Gyro Removal | (10) Remove the directional gyro from the airplane | Directional Gyro | Supprimer |
| inconnue | (7) Remove the turn coordinator from the airplane | Turn Coordinator | Supprimer |
| inconnue | (4) Remove compass from airplane | Compass | Supprimer |
| A. Remove the Marker Beacon Antenna | (4) Remove the screws that attach the antenna to the panel | Marker Beacon Antenna | Supprimer |
| A. Remove the EVS-600 Camera | (10) Use a nonmetallic scraper to carefully remove the sealant from the camera and spacer | EVS-600 Camera | Supprimer |
| A. Remove the KMH-880 Interface Adapter | (11) Remove the screws that attach the configuration module to the support bracket | KMH-880 Interface Adapter | Supprimer |
| A. Remove the Omnidirectional Antenna | (8) Remove the doubler and omnidirectional antenna from the airplane | Omnidirectional Antenna | Supprimer |
| A. KTA-810 Processor Removal | (10) Remove the rack assembly from the airplane | KTA-810 Processor | Supprimer |
| A. KCM-805 Configuration Module Removal | (6) Remove the screws that attach the configuration module to the support bracket | KCM-805 Configuration Module | Supprimer |
| A. Remove the GTS 800 Traffic Advisory System (TAS) Processor | (9) Carefully remove the processor by grasping it and pulling it it out of the mounting rack | GTS 800 Traffic Advisory System (TAS) Processor | Supprimer |
| A. Remove the GA58 Directional Antenna | (a) Lift the antenna away from the fuselage and carefully remove it | GA58 Directional Antenna | Supprimer |
| A. Remove Omni Antenna | (7) Remove omni antenna from airplane | Omni (Nav) Antenna | Supprimer |
| A. Remove Nav Antenna Coupler | 5) Remove nav antenna coupler from airplane | Nav. Antenna Coupler | Supprimer |
| A. Remove Navigation Indicator | (5) Remove navigation indicator from airplane | KI-209A and KI-208 Navigation Indicators | Supprimer |
| A. Remove the Integrated Avionics Unit | (1) Refer to Chapter 23, Communications - Maintenance Practices | GIA-63 NAVICOM | Supprimer |
| A. Remove GPS Receiver | (3) Pull GPS receiver from radio panel rack and remove from airplane | GPS Receiver | Supprimer |
| A. Remove GPS Antenna | (4) Remove GPS antenna and gasket from airplane | KA-92 GPS Antenna | Supprimer |
| A. ADF Receiver Removal | (3) Pull the. ADF receiver from the radio rack and remove from airplane | KR- 87 ADF Receiver | Supprimer |
| A. Remove Transponder | (3) Pull transponder from avionics radio panel rack and remove from airplane | KT-76C Transponder | Supprimer |
| A. Remove the KT-73 Transponder | (/) Remove the transponder from the airplane | KT-73 Mode S Transponder | Supprimer |
| A. Remove the Transponder | (7) Remove the transponder from the airplane | GTX-33 Transponder | Supprimer |
| A. Remove the Vacuum Pump | (7) Discard any damaged fittings or nuts with rounded corners | Vacuum Pump | Supprimer |
| A. Remove the Vacuum Manifold | 5) Remove the vacuum manifold from the airplane | Vacuum Manifold | Supprimer |
| A. Remove the Gyro Filter | (2) Remove the gyro filter | Gyro Filter | Supprimer |
| inconnue | (3) Remove the screws thata attach the vacuum gage to the instrument panel and remove the vacuum gage | Vacuum Gage | Supprimer |
| A. Cabin Door Removal | (4) Remove the cabin door from the airplane | Cabin Door | Supprimer |
| A. Cabin Door Weatherstrip Removal | (2) Use solvent to remove all remaining adhesive from the door surface | Cabin Door Weatherstrip | Supprimer |
| A. Cabin Door Latch Lock Removal | (3) Remove the locking arm pin from the locking arm and the catch base assembly | Cabin Door Latch Lock | Supprimer |
| A. Cabin Door Latch Assembly Removal | (6) Remove the latch assembly from the airplane | Cabin Door Latch Assembly | Supprimer |
| A. Cabin Door Lock Cam Assembly Removal | (4) Remove the cam assembly | Cabin Door Lock Cam Assembly | Supprimer |
| A. Cargo Door Removal | (3) Remove the cotter pins and remove the pins that attach the door | Cargo Door | Supprimer |
| A. Cargo Door Latch Assembly Removal | (4) Remove the screws that attach the door latch assembly and remove the door latch assembly | Forward Cargo Door Latch Assembly | Supprimer |
| A. Cargo Door Weatherstrip Removal | (4) Install the cargo door | Cargo Door Weatherstrip | Supprimer |
| A. Cargo Door Lock Assembly Removal | (3) Remove the cabin door lock assembly | Cargo Door Lock Assembly | Supprimer |
| A. Cargo Door Lock Cam Assembly Removal | (3) Remove the cam assembly | Cargo Door Lock Cam Assembly | Supprimer |
| A. Remove the Horizontal Stabilizer Abrasion Boot | (g) Remove the masking tape | Horizontal Stabilizer Abrasion Boot | Supprimer |
| A. Remove Windshield | (6) Clean sealer from inner sidewalls and bottom of retainers | Windshield | Supprimer |
| A. Remove Rear Window | (4) Remove window by lifting aft edge and pulling window aft. If difficulty is encountered, rivets securing retainer strips inside cabin may also be drilled out and retainer strips loosened or removed | Rear Window | Supprimer |
| A. Remove Side Window | (4) Remove the window from the airplane | Side Window | Supprimer |
| A. Remove Wing Tip | (5) Remove wing tip from wing | Wing Tip | Supprimer |
| inconnue | (a) Write the number of spacers that is removed for installation of the spinner | Spinner | Supprimer |
| A. Remove Engine | (36) Remove bolts attaching engine shock mounts to engine mount assembly. Slowly raise engine using hoist until engine is free of structure | Engine | Supprimer |
| A. Remove Cowl Flap | (3) Remove safety wire securing hinge pins to cowl flaps, pull hinge pins and remove cowl flaps | Cowl Flap | Supprimer |
| A. Remove the Cylinder Drain Can | (3) Remove the two bolts that attach the cylinder drain can to the engine compartment and remove the cylinder drain can from the airplane | Cylinder Drain Can | Supprimer |
| A. Remove Fuel Distribution Valve | (3) Remove nuts, bolts, washers and spacers securing fuel distribution valve to engine case | Fuel Distribution Valve | Supprimer |
| A. Remove the Manifold Pressure/Fuel Flow Indicator | (6) Disconnect the manifold pressure tube from the manifold pressure/fuel flow indicator | Manifold Pressure/Fuel Flow Indicator | Supprimer |
| A. Remove the Fuel Pressure Transducer | (5) Remove the fuel pressure transducer and packing from the union | Fuel Pressure Transducer | Supprimer |
| A. Remove the Fuel Flow Transducer | (7) Remove the fuel flow transducer from the airplane | Fuel Flow Transducer | Supprimer |
| inconnue | (7) Carefully pull throttle control through firewall and instrument panel removing lock washers and jamnuts, and remove from airplane | Throttle Control | Supprimer |
| A. Remove Fuel Mixture Control | (7) Carefully pull fuel mixture control through firewall and instrument panel and remove from airplane | Fuel Mixture Control | Supprimer |
| A. Remove the CHT Probe | (3) For non-turbo engines, Unscrew and remove the CHT probe from the Number 3 cylinder. For turbo engines, remove the CHT probe from the Number 5 cylinder | CHT Probe | Supprimer |
| A. Remove the Manifold Pressure Transducer | (4) Remove the manifold pressure transducer | Manifold Pressure Transducer | Supprimer |
| A. Engine/Airframe Unit Removal | (4) Remove the engine/airframe unit from the airplane | GEA-71 Engine/Airframe Unit | Supprimer |
| A. Remove the Air/Oil Separator Assembly | (5) Remove the air/oil separator from the airplane | Air/Oil Separator Assembly | Supprimer |
| inconnue | 4) Carefully remove the indicator from back of the instrument panel | Oil Pressure Indicator and Transducer | Supprimer |
| Remove the Transducer | (4) Remove the nutt that connects the transducer to the rear of the baffle and remove the transducer | Oil Pressure Indicator and Transducer | Supprimer |
| A. Remove the Sending Unit | (3) Loosen and remove the sending unit from the accessory case | Sending Unit | Supprimer |
| A. Remove the Starter | (5) Remove the bolt from the starter and remove starter from the engine | Starter | Supprimer |
| A. Remove Fuel/Air Control Unit | (7) Remove bolts, washers and nuts securing control unit to engine induction plenum. Cover induction plenum opening and place control unit in a sealed, dust free environment to prevent accumulation of foreign particles into unit | Fuel/Air Control Unit | Supprimer |
| A. Remove Brake Lining | 5) Center a 9/64-inch (3.58 mm) (or slightly smaller) punch in the rolled rivet and hit the punch sharply with a hammer. Punch out all rivets securing the linings to the back plate and pressure plate in the same manner | Brake Line Fairing | Supprimer |
| A. Remove parking Brake System | (8) Remove nut, washer, and bolt and remove pulley and brake cable from upper end of bellcrank | Main Landing Brake Clip | Supprimer |
| C. Remove the filler valve | 5) Remove filler valve | filler valve | Supprimer |
| inconnue | (4) After engine stops, move mixture control to idle cutoff position | ACS Ignittion Switch | Supprimer |